Top Searched #3dprinting products on 3dprintnerd.com

The v6 HotEnd Full Kit from E3D has been redesigned for your convenience from the ground up! This new hot end contains the same signature high temperature performance for high-temp printing, as well as increased functionality for printing soft and flexible filaments. The v6 HotEnd allows you to print a wide variety of materials, from soft and flexible to sturdy and strong. This is possible due to the PTFE (Polytetrafluoroethylene) liner tube through the hotend that you can extend into your extruder – this gives the ability to add the confinement and constraint needed to make excellent quality prints with flexible filaments. This technology opens new doors for your 3D printing aspirations. With High Temperature Performance, you can print with high-temp materials like Polycarbonate and Nylon – this also eliminates HotEnd meltdown failures that are common with PTFE designs. Even though the v6 has a PTFE liner inside the hotend the liner is never subjected to high temperatures so there is no risk of damaging the liner through overheating. Basically, this design is really in-tune with all the elements, so your prints will come out crisp and accurate. The v6 has cut back on a bunch of bulk. This clean-cut version’s overall length is only 62mm, and there are significant reductions in the X/Y dimensions by using the new injection moulded fan duct. Are you eager to start printing right away? Good. So are we – and that’s why here at MatterHackers we praise the v6 HotEnd. No adhesives, Kapton tape, or soldering is needed to get started. The new v6 simply locks into place with a little screw, high-temp glass sleeving is used to insulate the thermistor legs. This makes installing the hotend (as well as removing) a quick and smooth process compared to earlier methods involving various adhesives.The parts of the hotend just screw together, and the fan duct naturally clips in – this can be manipulated in different ways to suit your setup preference.

  • The v6 HotEnd Full Kit from E3D has been redesigned for your convenience from the ground up!
  • This new hot end contains the same signature high temperature performance for high-temp printing, as well as increased functionality for printing soft and flexible filaments.
  • The v6 HotEnd allows you to print a wide variety of materials, from soft and flexible to sturdy and strong.
  • With High Temperature Performance, you can print with high-temp materials like Polycarbonate and Nylon
  • Basically, this design is really in-tune with all the elements, so your prints will come out crisp and accurate.

E3D V6 All Metal HotEnd Full Kit – 3mm Universal (with Bowden add-on) (24v). The package contains the following parts:

Metal parts

  • 1 x Aluminium Heatsink (Contains brass embedded bowden coupling ring pre-fitted in top)
  • 1 x Stainless Steel Heatbreak
  • 1 x Brass Nozzle (0.4mm)
  • 1 x Aluminium Heater Block

Electronics

  • 1 x 100K Semitec NTC thermistor
  • 1 x 24v Heater Cartridge
  • 1 x 24v 30x30x10mm fan
  • 1 x High Temperature Fiberglass Wire – for Thermistor (150mm)
  • 2 x 0.75mm Ferrules – for Solder-Free Wire Joins

Fixings

  • 4 x Plastfast30 3.0 x 16 screws to attach the fan to the fan duct
  • 1 x M3x3 socket dome screw and M3 washer to clamp thermistor
  • 1 x M3x10 socket dome screw to clamp the heater block around the heater cartridge
  • 1 x Fan Duct (Injection Moulded PC)

Bowden add-on

  • 800mm of appropriately sized PTFE tubing.
  • 1 x Screw in Coupler for extruder end of tubing.

Please check the manufacturer’s website for assembly instructions and detailed technical information.

  • E3D V6 all metal hotend 0.4mm nozzle for 3mm filament (with Bowden add-on) (24V).
  • The E3D V6 has been redesigned from the ground up: smaller, easier and higher performance.
  • Use up to 300C with the supplied thermistor for Polycarbonate, Nylon, PLA, ABS and more.
  • Original E3D package. Assembly instruction available on E3D website.
  • Fast free shipping from 3DMakerWorld (Continental US)

Specifications:
Product descrition:

Heat tube: 12V 40W,1m long

Thermistor: 100K NTC B 3950 ±1% ,1m long

Throat: Stainless Steel with teflon tube

With free Copper Cap

This 3D Printer J-head Hotend is applied for 3.00mm short-Distance Filament Bowden extruder

After improvement by our technical personnel,the unique design let this J-head Hotend is better than that before

Package listing:

1x J-head/E3D Hotend for short-Distance Bowden extruder

  • Aluminum Heater Block:20mm*20mm*10mm
  • Ultimaker Nozzle:0.2mm 0.3mm 0.4mm 0.5mm
  • M6 X 30 Nozzle Throat (Teflon included)
  • Ceramic Cartridge Heater:12V 40W ;100Kohm NTC Thermistors thermistor

E3D Lite6 Full Kit – 1.75mm Universal (Direct) (12v). The package contains the following parts:

Metal parts

  • 1 x Stainless Heatsink (Contains brass embedded bowden coupling ring pre-fitted in top)
  • 1 x Aluminium Heater Block
  • 1 x Brass Nozzle (0.4mm)

Electronics

  • 1 x 100K Semitec NTC thermistor
  • 1 x 12v Heater Cartridge
  • 1 x 12v 30x30x10mm fan
  • 1 x High Temperature Fiberglass Wire – for Thermistor (150mm)
  • 2 x 0.75mm Ferrules – for Solder-Free Wire Joins

Fixings

  • 4 x Plastfast30 3.0 x 16 screws to attach the fan to the fan duct
  • 1 x M3x3 socket dome screw and M3 washer to clamp thermistor
  • 1 x M3x10 socket dome screw to clamp the heater block around the heater cartridge
  • 1 x Fan Duct (Injection Moulded Red Transparent Polycarbonate)
  • 1 x Small Black Plastic Collet (For securing PTFE tubing into embedded bowden coupling installed in heatsink)

Please check the manufacturer’s website for assembly instructions and detailed technical information.

  • E3D Lite 6 hotend 0.4mm nozzle for 1.75mm filament (Direct) (12V).
  • “Mostly Metal” design with PTFE liner for exceptional reliability and servability.
  • Use up to 240C for standard materials, such as ABS and PLA.
  • Original E3D package. Assembly instruction available on E3D website.
  • Fast free shipping from 3DMakerWorld (Continental US)

E3D V6 All Metal HotEnd Full Kit – 1.75mm Universal (Direct) (24v). The package contains the following parts:

Metal parts

  • 1 x Aluminium Heatsink (Contains brass embedded bowden coupling ring pre-fitted in top)
  • 1 x Stainless Steel Heatbreak
  • 1 x Brass Nozzle (0.4mm)
  • 1 x Aluminium Heater Block

Electronics

  • 1 x 100K Semitec NTC thermistor
  • 1 x 24v Heater Cartridge
  • 1 x 24v 30x30x10mm fan
  • 1 x High Temperature Fiberglass Wire – for Thermistor (150mm)
  • 2 x 0.75mm Ferrules – for Solder-Free Wire Joins

Fixings

  • 4 x Plastfast30 3.0 x 16 screws to attach the fan to the fan duct
  • 1 x M3x3 socket dome screw and M3 washer to clamp thermistor
  • 1 x M3x10 socket dome screw to clamp the heater block around the heater cartridge
  • 1 x Fan Duct (Injection Moulded PC)

Please check the manufacturer’s website for assembly instructions and detailed technical information.

  • E3D V6 all metal hotend 0.4mm nozzle for 1.75mm filament (Direct) (24V).
  • The E3D V6 has been redesigned from the ground up: smaller, easier and higher performance.
  • Use up to 300C with the supplied thermistor for Polycarbonate, Nylon, PLA, ABS and more.
  • Original E3D package. Assembly instruction available on E3D website.
  • Fast free shipping from 3DMakerWorld (Continental US)

The E3D Volcano is the earth-shattering eruption that the 3D printing world wants – nay – needs! Larger prints can now be accomplished in nearly half the time with the addition of the Volcano to any E3D Hotend (except the cyclops).

  • The E3D Volcano is the earth-shattering eruption that the 3D printing world wants – nay – needs!
  • Print using larger layer heights faster than ever
  • Works with all E3D V6 HotEnds

Known as the little brother of the v6 Hotends, Lite6 is a lower cost hotend, with a more modest specification, but still a great option for beginners and those on a budget. Lite6 is reliable, puts out great prints, and meets the budget of those who are getting started in 3D Printing. Lite6 is still compatible with all of your E3D v6 nozzles and can be used as both a direct HotEnd or used with a bowden coupling system right out of the box!

  • NOT All Metal
  • Bowden Tube Included
  • ABS and PLA ONLY

The v6 HotEnd Full Kit from E3D has been redesigned for your convenience from the ground up! This new hot end contains the same signature high temperature performance for high-temp printing, as well as increased functionality for printing soft and flexible filaments. The v6 HotEnd allows you to print a wide variety of materials, from soft and flexible to sturdy and strong. This is possible due to the PTFE (Polytetrafluoroethylene) liner tube through the hotend that you can extend into your extruder – this gives the ability to add the confinement and constraint needed to make excellent quality prints with flexible filaments. This technology opens new doors for your 3D printing aspirations. With High Temperature Performance, you can print with high-temp materials like Polycarbonate and Nylon – this also eliminates HotEnd meltdown failures that are common with PTFE designs. Even though the v6 has a PTFE liner inside the hotend the liner is never subjected to high temperatures so there is no risk of damaging the liner through overheating. Basically, this design is really in-tune with all the elements, so your prints will come out crisp and accurate. The v6 has cut back on a bunch of bulk. This clean-cut version’s overall length is only 62mm, and there are significant reductions in the X/Y dimensions by using the new injection moulded fan duct. Are you eager to start printing right away? Good. So are we – and that’s why here at MatterHackers we praise the v6 HotEnd. No adhesives, Kapton tape, or soldering is needed to get started. The new v6 simply locks into place with a little screw, high-temp glass sleeving is used to insulate the thermistor legs. This makes installing the hotend (as well as removing) a quick and smooth process compared to earlier methods involving various adhesives.The parts of the hotend just screw together, and the fan duct naturally clips in – this can be manipulated in different ways to suit your setup preference.

  • The v6 HotEnd Full Kit from E3D has been redesigned for your convenience from the ground up!
  • This new hot end contains the same signature high temperature performance for high-temp printing, as well as increased functionality for printing soft and flexible filaments.
  • The v6 HotEnd allows you to print a wide variety of materials, from soft and flexible to sturdy and strong.
  • With High Temperature Performance, you can print with high-temp materials like Polycarbonate and Nylon
  • Basically, this design is really in-tune with all the elements, so your prints will come out crisp and accurate.

The v6 HotEnd Full Kit from E3D has been redesigned for your convenience from the ground up! This new hot end contains the same signature high temperature performance for high-temp printing, as well as increased functionality for printing soft and flexible filaments. The v6 HotEnd allows you to print a wide variety of materials, from soft and flexible to sturdy and strong. This is possible due to the PTFE (Polytetrafluoroethylene) liner tube through the hotend that you can extend into your extruder – this gives the ability to add the confinement and constraint needed to make excellent quality prints with flexible filaments. This technology opens new doors for your 3D printing aspirations. With High Temperature Performance, you can print with high-temp materials like Polycarbonate and Nylon – this also eliminates HotEnd meltdown failures that are common with PTFE designs. Even though the v6 has a PTFE liner inside the hotend the liner is never subjected to high temperatures so there is no risk of damaging the liner through overheating. Basically, this design is really in-tune with all the elements, so your prints will come out crisp and accurate. The v6 has cut back on a bunch of bulk. This clean-cut version’s overall length is only 62mm, and there are significant reductions in the X/Y dimensions by using the new injection moulded fan duct. Are you eager to start printing right away? Good. So are we – and that’s why here at MatterHackers we praise the v6 HotEnd. No adhesives, Kapton tape, or soldering is needed to get started. The new v6 simply locks into place with a little screw, high-temp glass sleeving is used to insulate the thermistor legs. This makes installing the hotend (as well as removing) a quick and smooth process compared to earlier methods involving various adhesives.The parts of the hotend just screw together, and the fan duct naturally clips in – this can be manipulated in different ways to suit your setup preference.

  • The v6 HotEnd Full Kit from E3D has been redesigned for your convenience from the ground up!
  • This new hot end contains the same signature high temperature performance for high-temp printing, as well as increased functionality for printing soft and flexible filaments.
  • The v6 HotEnd allows you to print a wide variety of materials, from soft and flexible to sturdy and strong.
  • With High Temperature Performance, you can print with high-temp materials like Polycarbonate and Nylon
  • Basically, this design is really in-tune with all the elements, so your prints will come out crisp and accurate.

The Jhead hotends are the original, made in USA by the inventor. This kit contains (1) Hot end with a 0.5 mm nozzle to use with 1.75 filament (PLA or ABS) (2) Resistor (3) Thermistor (4) PTFE Teflon Tubing for the resistor and thermistor.

  • Original, made by the inventor, not made in China
  • Lightweight. Prints fast. Heats up fast. Accurate temperature reporting. Prints reliably with both ABS and PLA. (PLA may require a small fan to provide air-flow through the cooling vents which are milled in the sides of the nozzle holder.)
  • Easily interfaces with the most popular RepRap extruders, such as Wade’s Extuder and Greg Frost’s Hinged Accessible Extruder.
  • Simple design. Number of custom machined parts is kept to a minimum.
  • Resistor is used as a heater. No need to wrap nichrome wire or to bake a heater core. Heat transmission is improved because there is no thermal junction where a separate heater would screw onto the nozzle.

The Jhead hotends are the original, made in USA by the inventor. This kit contains (1) Hot end with a 0.4 mm nozzle to use with 1.75 filament (PLA or ABS) (2) Resistor (3) Thermistor (4) PTFE Teflon Tubing for the resistor and thermistor.

  • Original, made by the inventor, not made in China
  • Lightweight. Prints fast. Heats up fast. Accurate temperature reporting. Prints reliably with both ABS and PLA. (PLA may require a small fan to provide air-flow through the cooling vents which are milled in the sides of the nozzle holder.)
  • Easily interfaces with the most popular RepRap extruders, such as Wade’s Extuder and Greg Frost’s Hinged Accessible Extruder.
  • Simple design. Number of custom machined parts is kept to a minimum.
  • Resistor is used as a heater. No need to wrap nichrome wire or to bake a heater core. Heat transmission is improved because there is no thermal junction where a separate heater would screw onto the nozzle.

The Jhead hotends are the original, made in USA by the inventor. This kit contains (1) Hot end with a 0.35 mm nozzle to use with 1.75 filament (PLA or ABS) (2) Resistor (3) Thermistor (4) PTFE Teflon Tubing for the resistor and thermistor.

  • Original, made by the inventor, not made in China
  • Lightweight. Prints fast. Heats up fast. Accurate temperature reporting. Prints reliably with both ABS and PLA. (PLA may require a small fan to provide air-flow through the cooling vents which are milled in the sides of the nozzle holder.)
  • Easily interfaces with the most popular RepRap extruders, such as Wade’s Extuder and Greg Frost’s Hinged Accessible Extruder.
  • Simple design. Number of custom machined parts is kept to a minimum.
  • Resistor is used as a heater. No need to wrap nichrome wire or to bake a heater core. Heat transmission is improved because there is no thermal junction where a separate heater would screw onto the nozzle.

The Jhead hotends are the original, made in USA by the inventor. This kit contains (1) Hot end with a 0.4 mm nozzle to use with 3.0 filament (PLA or ABS) (2) Resistor (3) Thermistor (4) PTFE Teflon Tubing for the resistor and thermistor.

  • Original, made by the inventor, not made in China. Version Mk V-BV. Thermistor Part Number: 104GT-2.
  • Lightweight. Prints fast. Heats up fast. Accurate temperature reporting. Prints reliably with both ABS and PLA. (PLA may require a small fan to provide air-flow through the cooling vents which are milled in the sides of the nozzle holder.)
  • Easily interfaces with the most popular RepRap extruders, such as Wade’s Extuder and Greg Frost’s Hinged Accessible Extruder.
  • Simple design. Number of custom machined parts is kept to a minimum.
  • Resistor is used as a heater. No need to wrap nichrome wire or to bake a heater core. Heat transmission is improved because there is no thermal junction where a separate heater would screw onto the nozzle.

The Jhead hotends are the original, made in USA by the inventor. This kit contains (1) Hot end with a 0.35 mm nozzle to use with 3.0 filament (PLA or ABS) (2) Resistor (3) Thermistor (4) PTFE Teflon Tubing for the resistor and thermistor.

  • Original, made by the inventor, not made in China. Version Mk V-BV. Thermistor Part Number: 104GT-2.
  • Lightweight. Prints fast. Heats up fast. Accurate temperature reporting. Prints reliably with both ABS and PLA. (PLA may require a small fan to provide air-flow through the cooling vents which are milled in the sides of the nozzle holder.)
  • Easily interfaces with the most popular RepRap extruders, such as Wade’s Extuder and Greg Frost’s Hinged Accessible Extruder.
  • Simple design. Number of custom machined parts is kept to a minimum.
  • Resistor is used as a heater. No need to wrap nichrome wire or to bake a heater core. Heat transmission is improved because there is no thermal junction where a separate heater would screw onto the nozzle.

The Jhead hotends are the original, made in USA by the inventor. This kit contains (1) Hot end with a 0.5 mm nozzle to use with 3.0 filament (PLA or ABS) (2) Resistor (3) Thermistor (4) PTFE Teflon Tubing for the resistor and thermistor.

  • Original, made by the inventor, not made in China. Version Mk V-BV. Thermistor Part Number: 104GT-2.
  • Lightweight. Prints fast. Heats up fast. Accurate temperature reporting. Prints reliably with both ABS and PLA. (PLA may require a small fan to provide air-flow through the cooling vents which are milled in the sides of the nozzle holder.)
  • Easily interfaces with the most popular RepRap extruders, such as Wade’s Extuder and Greg Frost’s Hinged Accessible Extruder.
  • Simple design. Number of custom machined parts is kept to a minimum.
  • Resistor is used as a heater. No need to wrap nichrome wire or to bake a heater core. Heat transmission is improved because there is no thermal junction where a separate heater would screw onto the nozzle.

Great companion to 3D printer !!

  • Weight: 0.18KG
  • for 2*4mm PTFE pipe
  • for 1.75mm Filament
  • Aluminium Alloy
  • Oxidation treatment

SainSmart LCD 12864 with Controller contains a SD-Card reader, an rotary encoder and a 128 Character x 64 Line LCD display. You can easy connect it to your Ramps board using the “smart adapter” included. After connecting this panel to your Ramps you don’t need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card.

SainSmart Mechanical Endstop perfect for any 3D printer also for use on CNC machines and other electronic applications.

SainSmart SD Ramps: Breakout board for the microSD socket that is not much bigger than your fingernail. Compatible with the SPI interface found on any SD card, this tiny form factor was created for cell phone storage and is perfect for your next 3D printer project! Board comes fully assembled and tested.The bare socket is available.

SainSmart Heatbed MK2,Borosilicate Glass, Aluminium Bed Mount Plate is the latest and the best type of heatbed money can buy as of today. 100% compatible with all Prusa and Mendel 3d printer variants. (We will provide you another two 100K ohm thermistor as a gift.

Package Content:

1 x RAMPS 1.4
1 x Mega 2560 R3
5 x A4988 driver
1 x LCD 12864 With Controller
1 x SD card breakout For ramps
2 x Cooler Fan for 3D ramps
6 x Mechanical Endstop with cable
1 x RAMPS 1.4 wiring cable
1 x Heatbed MK2b
2 x thermistor For headbed(100K ohm)
1 x Borosilicate Glass
1 x Aluminium Bed Mount Plate
5 x NEMA 17 Stepper Motors
1 x Assembled J-head Hotend Nozzle.
5 x GT2 20T Aluminum Pulley
1 x GT2 Timing Belt
1 x USB Cable

Note: If you need any technical support of instructions, please contact our customer service.

  • Sainsmart A4988 driver is a carrier board or breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection by Pololu; we therefore recommend careful reading of the A4988 datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2 A output current per coil. We will provide you additional heat sink for you as a gift.
  • Sainsmart Mega2560 R3 is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal oscillator. With the bootloader, download the program directly via USB without having to go through other external writer. Supply part of the optional USB power, or as an external power using the AC-to-DC adapter and battery. Arduino development IDE interface is based on open-source principles, allows you to free download for use in project work, school teaching, motor control, interactive works.
  • Sainsmart RAMPS 1.4 is a Mega Pololu Shield, or RAMPS for short,designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces a Mega with the powerful MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on a MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack. This board is mostly based on Adrian’s Pololu_Electronics and work by Tonok. Copper etch resists methods suggested by Vik. Also inspired by Vik’s work with EasyDrivers. circuit design based mostly on Adrian’s Pololu_Electronics Joaz at RepRapSource.com supplied initial pin definitions and many design improvements. Much inspiration, suggestions, and ideas from Prusajr, Kliment, Maxbots, Rick, and many others in the RepRap community.

SainSmart LCD 12864 with Controller contains a SD-Card reader, an rotary encoder and a 128 Character x 64 Line LCD display. You can easy connect it to your Ramps board using the “smart adapter” included. After connecting this panel to your Ramps you don’t need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card.

SainSmart Mechanical Endstop perfect for any 3D printer also for use on CNC machines and other electronic applications.

SainSmart SD Ramps: Breakout board for the microSD socket that is not much bigger than your fingernail. Compatible with the SPI interface found on any SD card, this tiny form factor was created for cell phone storage and is perfect for your next 3D printer project! Board comes fully assembled and tested.The bare socket is available.

SainSmart Heatbed MK2,Borosilicate Glass, Aluminium Bed Mount Plate is the latest and the best type of heatbed money can buy as of today. 100% compatible with all Prusa and Mendel 3d printer variants. (We will provide you another two 100K ohm thermistor as a gift.

Package Content:

1 x RAMPS 1.4
1 x Mega 2560 R3
5 x A4988 driver
1 x LCD 12864 With Controller
1 x SD card breakout For ramps
2 x Cooler Fan for 3D ramps
6 x Mechanical Endstop with cable
1 x RAMPS 1.4 wiring cable
1 x Heatbed MK2b
2 x thermistor For headbed(100K ohm)
1 x Borosilicate Glass
1 x Aluminium Bed Mount Plate
5 x NEMA 17 Stepper Motors
1 x Assembled J-head Hotend Nozzle.
5 x GT2 20T Aluminum Pulley
1 x GT2 Timing Belt
1 x USB Cable

Note: If you need any technical support of instructions, please contact our customer service.

  • Sainsmart A4988 driver is a carrier board or breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection by Pololu; we therefore recommend careful reading of the A4988 datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2 A output current per coil. We will provide you additional heat sink for you as a gift.
  • Sainsmart Mega2560 R3 is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal oscillator. With the bootloader, download the program directly via USB without having to go through other external writer. Supply part of the optional USB power, or as an external power using the AC-to-DC adapter and battery. Arduino development IDE interface is based on open-source principles, allows you to free download for use in project work, school teaching, motor control, interactive works.
  • Sainsmart RAMPS 1.4 is a Mega Pololu Shield, or RAMPS for short,designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces a Mega with the powerful MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on a MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack. This board is mostly based on Adrian’s Pololu_Electronics and work by Tonok. Copper etch resists methods suggested by Vik. Also inspired by Vik’s work with EasyDrivers. circuit design based mostly on Adrian’s Pololu_Electronics Joaz at RepRapSource.com supplied initial pin definitions and many design improvements. Much inspiration, suggestions, and ideas from Prusajr, Kliment, Maxbots, Rick, and many others in the RepRap community.

Sainsmart LCD 2004 with Controller contains a SD-Card reader, an rotary encoder and a 20 Character x 4 Line LCD display. You can easy connect it to your Ramps board using the “smart adapter” included. After connecting this panel to your Ramps you don’t need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card.

SainSmart Mechanical Endstop perfect for any 3D printer also for use on CNC machines and other electronic applications.

SainSmart SD Ramps: Breakout board for the microSD socket that is not much bigger than your fingernail. Compatible with the SPI interface found on any SD card, this tiny form factor was created for cell phone storage and is perfect for your next 3D printer project! Board comes fully assembled and tested.The bare socket is available.

SainSmart Heatbed MK2b,Borosilicate Glass, Aluminium Bed Mount Plate is the latest and the best type of heatbed money can buy as of today. 100% compatible with all Prusa and Mendel 3d printer variants. (We will provide you another two 100K ohm thermistor as a gift.) Size: 214mm x 214mm. Etching: 35um copper 12V/24V compatible. Laminate: FR4 1.6mm.

Package List:

1 x RAMPS 1.4
1 x Mega 2560 R3
5 x A4988 driver
1 x LCD 2004 With Controller
1 x SD card breakout For ramps
2 x Cooler Fan for 3D ramps
6 x Mechanical Endstop with cable
1 x RAMPS 1.4 wiring cable
1 x Heatbed MK2b
2 x thermistor For headbed(100K ohm)
1 x Borosilicate Glass
1 x Aluminium Bed Mount Plate
5 x NEMA 17 Stepper Motors
1 x Assembled J-head Hotend Nozzle.
5 x GT2 20T aluminum pulley
1 x GT2 Timing Belt
1 x USB Cable

  • This is the new SainSmart 3D Printer Starter Kit, developed specially for those beginners who are interested in 3D printer.
  • You will have a complete set of Sainsmart’s most common and useful electronic components.
  • Sainsmart A4988 driver is a carrier board or breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection by Pololu; we therefore recommend careful reading of the A4988 datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2 A output current per coil. We will provide you additional heat sink for you as a gift.
  • Sainsmart Mega2560 R3 is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal oscillator. With the bootloader, download the program directly via USB without having to go through other external writer. Supply part of the optional USB power, or as an external power using the AC-to-DC adapter and battery. Arduino development IDE interface is based on open-source principles, allows you to free download for use in project work, school teaching, motor control, interactive works.
  • Sainsmart RAMPS 1.4 is a Mega Pololu Shield, or RAMPS for short,designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces a Mega with the powerful MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on a MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack. This board is mostly based on Adrian’s Pololu_Electronics and work by Tonok. Copper etch resists methods suggested by Vik. Also inspired by Vik’s work with EasyDrivers. circuit design based mostly on Adrian’s Pololu_Electronics Joaz at RepRapSource.com supplied initial pin definitions and many design improvements. Much inspiration, suggestions, and ideas from Prusajr, Kliment, Maxbots, Rick, and many others in the RepRap community.

Overview

The 2.0 version is a high performance hotend for use with RepRap and other 3D printers,making your printing even faster. The hot end comes completely assembled: wire it to your electronics and it is ready to print. It now includes an aluminum mount plate and aluminum heat sinks. The 2.0 also brings changes to the nozzle, heater block, and threaded extension with harder aluminum and revised thread profile for more reliable nozzle changes.

Optional nozzle sizes are available from 0.3mm to 0.5mm,easy to disassemble and replace.With the optional PTFE tube, you can print both 1.75mm and 3mm filament.

The hotend will come with two nozzles,you could choose one of them,the extra one is 0.4mm.

Features

Aluminum Block Resistor Hotend
Easily assembled and torn down with no glue or ceramic
Wire Strain Relief
Includes machined aluminum and steel parts, and laser cut wooden parts
Includes pre-crimped wiring
resistance of resistor 4.7Ω
resistor rated power 8W
Nozzle material: Aluminum 6063
Nozzle thred: M10,pitch 1.5mm

Package list

1 x SainSmart Reprap Hot End Hotend V2.0
1 x nozzle(Your choice)
1x extra 0.4mm nozzle

  • Aluminum Block Resistor Hotend
  • Easily assembled and torn down with no glue or ceramic
  • Includes machined aluminum and steel parts, and laser cut wooden parts
  • Includes pre-crimped wiring
  • Wire Strain Relief

SainSmart LCD 12864 with Controller contains a SD-Card reader, an rotary encoder and a 128 Character x 64 Line LCD display. You can easy connect it to your Ramps board using the “smart adapter” included. After connecting this panel to your Ramps you don’t need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card.

SainSmart Mechanical Endstop perfect for any 3D printer also for use on CNC machines and other electronic applications.

SainSmart SD Ramps: Breakout board for the microSD socket that is not much bigger than your fingernail. Compatible with the SPI interface found on any SD card, this tiny form factor was created for cell phone storage and is perfect for your next 3D printer project! Board comes fully assembled and tested.The bare socket is available.

SainSmart Heatbed MK2b,Borosilicate Glass, Aluminium Bed Mount Plate is the latest and the best type of heatbed money can buy as of today. 100% compatible with all Prusa and Mendel 3d printer variants. (We will provide you another two 100K ohm thermistor as a gift.) Size: 214mm x 214mm. Etching: 35um copper 12V/24V compatible. Laminate: FR4 1.6mm.

Package List:

1 x RAMPS 1.4
1 x Mega 2560 R3
5 x A4988 driver
1 x LCD 12864 With Controller
1 x SD card breakout For ramps
2 x Cooler Fan for 3D ramps
6 x Mechanical Endstop with cable
1 x RAMPS 1.4 wiring cable
1 x Heatbed MK2b
2 x thermistor For headbed(100K ohm)
1 x Borosilicate Glass
1 x Aluminium Bed Mount Plate
5 x NEMA 17 Stepper Motors
1 x Assembled J-head Hotend Nozzle.
5 x GT2 20T Aluminum Pulley
1 x GT2 Timing Belt
1 x USB Cable

  • This is the new SainSmart 3D Printer Starter Kit, developed specially for those beginners who are interested in 3D printer.
  • You will have a complete set of Sainsmart’s most common and useful electronic components.
  • Sainsmart A4988 driver is a carrier board or breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection by Pololu; we therefore recommend careful reading of the A4988 datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2 A output current per coil. We will provide you additional heat sink for you as a gift.
  • Sainsmart Mega2560 R3 is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal oscillator. With the bootloader, download the program directly via USB without having to go through other external writer. Supply part of the optional USB power, or as an external power using the AC-to-DC adapter and battery. Arduino development IDE interface is based on open-source principles, allows you to free download for use in project work, school teaching, motor control, interactive works.
  • Sainsmart RAMPS 1.4 is a Mega Pololu Shield, or RAMPS for short,designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces a Mega with the powerful MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on a MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack. This board is mostly based on Adrian’s Pololu_Electronics and work by Tonok. Copper etch resists methods suggested by Vik. Also inspired by Vik’s work with EasyDrivers. circuit design based mostly on Adrian’s Pololu_Electronics Joaz at RepRapSource.com supplied initial pin definitions and many design improvements. Much inspiration, suggestions, and ideas from Prusajr, Kliment, Maxbots, Rick, and many others in the RepRap community.

Description
Cet item est une extrudeuse imprimante 3D, qui est faite d’un matériau métallique résistant. Il est adapté pour imprimante Hotend V2.0 GT5 3D. Facile à installer et à haute performance, bon pour remplacer votre extrudeuse vieux ou endommagé.

Caractéristiques
-Matériaux applicables: disponible 3mm / 1,75 mm PLA et ABS (non inclus).
-Impression précision: 0,1 mm.
-Matériau: métal.
-Débit buse: sujet 24cc / h.
-Tension: 12V.
-Méthode de moulage: FDM fondre de stratification.
-Dimensions: 88 * 42 * 101 mm.
-Buse extrusion: 0,3 mm, 0,35 mm, 0. 4 mm, 0,5 mm.
-Thermistances: 100K 1 % précision NTC thermistances.

Paquet y compris
1 * Kit de buse Hotend V2.0 GT5 extrudeuse tête d’imprimante 3D

  • Matériaux applicables: disponible 3mm1.75mm PLA et ABS (non inclus).
  • Précision d’impression: 0,1 mm. Matériau: métal. Dimensions: 88 * 42 * 101 mm.
  • Débit de la buse: environ 24cc h. tension: 12V.
  • Méthode de moulage: FDM fondre de stratification.
  • Buse d’extrusion: 0,3 mm, 0,35 mm, 0. 4 mm, 0,5 mm.

Description
RepRap 3D imprimantes hotend version 2.0 est un hotend de haute performance qui vous permet d’imprimer plus rapidement. Extrémité chaude sont entièrement Assemblée : il se connecte à vos produits électroniques, prêts à imprimer. Il contient maintenant un plat en aluminium et un radiateur. V2.0 apporte également des changements dans la buse, blocs de chauffage, Duralumin et changements de Jet plus fiables révisé extension de profil fileté fileté.

Caractéristiques
-Couleur : comme sur les photos.
-Résistance en aluminium Hotend
-Facilement assemblés sans colle ou porcelaine vers le bas
-Le serre fil.
-Comprend l’usinage de l’aluminium et l’acier inoxydable, découpé au laser des pièces en bois.
-Comprend des câbles de précontrainte.
-Tailles de buse facultatif au choix allant de 0,25 mm à 0,75 mm. – avec tuyau PTFE en option, vous pouvez imprimer le filament est 1,75 mm.
-Assemblée des hotend est de 0,4 mm et buse de 0,35 mm.

Paquet y compris
1 * imprimante 3D RepRap V2.0
1 * 0. 35 mm Buse
1 * 0. 4 mm Buse

  • Résistance en aluminium Hotend. Serre-fil.
  • Facilement assemblé sans colle ni porcelaine vers le bas
  • Inclut l’usinage de l’aluminium et l’acier inoxydable, découpé au laser des pièces en bois.
  • Comprend des câbles de précontrainte.
  • Tailles de buse en option au choix allant de 0,25 mm à 0,75 mm. – avec tuyau PTFE en option, vous pouvez imprimer le filament est 1,75 mm.